陕北沙漠区浅埋厚煤层开采潜水位及生态响应

煤炭开采造成上覆岩层破裂、移动，破坏了矿区含（隔）水层结构，改变了地表水及地下水循环演化状态，对浅表层生态环境造成严重影响，引发一系列环境地质问题。为深入研究沙漠地区厚煤层开采给潜水位及生态环境造成的影响，以毛乌素沙漠金鸡滩矿为例，对水文地质条件进行了研究，采用数值模拟的方法，模拟了沙漠区厚煤层开采潜水位的变化，并通过采动潜水位监测数据验证了预测结果。调查分析了研究区及周边地表生态环境现状，预测采后潜水位基本满足植物生长需求，对生态环境影响不大。     

汽车安全带固定点失效分析及结构优化

以乘用车后排安全带固定点为对象，基于安全带固定点强度试验结果，通过有限元方法建立模型，简化并调试有限元模型，进行试验对标分析。经过对标后，有限元分析结果与试验结果基本吻合。然后基于对标后的有限元模型对结构进行优化，提高安全带固定点强度，提出优化方案，并通过试验验证，满足法规要求。通过利用CAE分析技术在产品开发过程中的应用，有效找到问题原因并有针对性地加以优化，从而缩短开发周期和节约成本。     

Continuous Flow Fabrication of Block Copolymer–Grafted Silica Micro‐Particles in Environmentally Friendly Water/Ethanol Media

Polymer‐grafted inorganic particles (PGIPs) are attractive building blocks for numerous chemical and material applications. Surface‐initiated controlled radical polymerization (SI‐CRP) is the most feasible method to fabricate PGIPs. However, a conventional in‐batch reaction still suffers from several disadvantages, including time‐consuming purification processes, low grafting efficiency, and possible gelation problems. Herein, a facile method is demonstrated to synthesize block copolymer–grafted inorganic particles, that is, poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMEMA)‐b‐poly(N‐isopropylacrylamide) (PNIPAM)–grafted silica micro‐particles using continuous flow chemistry in an environmentally friendly aqueous media. Immobilizing the chain transfer agent and subsequent SI‐CRP can be accomplished sequentially in a continuous flow system, avoiding multi‐step purification processes in between. The chain length (MW) of the grafted polymers is tunable by adjusting the flow time or monomer concentration, and the narrower molar mass dispersity (Р< 1.4) of the grafted polymers reveals the uniform polymer chains on the particles. Moreover, compared with the in‐batch reaction at the same condition, the continuous system also suppresses possible gelation problems.     

Passive micromixer with baffles distributed on both sides of microchannels based on the Koch fractal principle

Since the beginning of the 21st Century, the development of microfluidic chip technology has been very rapid and has attracted the attention of more and more scholars. As an important part of the microfluidic chip, the performance of the micromixer is critical. The fractal structure in the microchannels helps to improve the mixing performance of the micromixer and improve the mixing efficiency of the micromixer. The research results of other scholars are of great significance to the research of the present paper, which mainly studies the effect of changing the baffle state on the mixing efficiency of the micromixer based on the Koch fractal principle. Through simulation analysis, it was found that the mixing efficiency of the baffles distributed on both sides of the microchannel was higher than the mixing efficiency of the baffles distributed on the microchannel side. When the distance between adjacent baffles was divided into 0.15, 0.25 and 0.35 mm, simulated data suggested that the baffle distance of 0.15 mm was best. Increasing the number of baffles from six to eight groups increased the mixing path of the fluid in the microchannel and improved mixing efficiency. A comparison of mixing efficiencies of the 0°, 15° and 30° baffle angles revealed that very significant improvement in mixing efficiency was obtained at 30°. © 2019 Society of Chemical Industry     

后纵臂的断裂原因分析

汽车在试验场行驶21 000 km后发现后纵臂断裂，该类后纵臂曾多次发生断裂故障。后纵臂在使用过程中受拉、压、扭等复杂载荷。通过对后纵臂进行外观观察，对其断口进行宏、微观观察，并对后纵臂进行金相组织检查、硬度检查及有限元模拟，确认后纵臂的失效性质，并分析其断裂原因。结果表明:后纵臂的失效性质为疲劳断裂；后纵臂的断裂过程为:在压应力作用下后纵臂中间安装孔处首先发生失稳变形，当后纵臂再次受拉时最大应力转移到中间安装孔处，在交变载荷的作用下发生疲劳开裂。适当增加后纵臂的厚度以提高其刚度，厚度增加后的后纵臂未再发生过类似的断裂故障。     

长走向平行钒铁矿体协同开采方案研究

七角井矿区的钒、铁双层矿体走向长度超4 km且呈近似平行产出，下盘铁矿开采时损失贫化率高且上盘钒矿资源保护难度大。根据钒铁矿体走向长、近平行产出、厚度负相关、空区隐患大的开采技术条件 特征，采用平面分区、开采时序规划、采矿方法优化、区域稳定性控制等技术来实现钒铁矿协同开采。根据铁矿“中间厚、两端薄”、钒矿“中间薄、两端厚”的形态特征，将长走向的钒铁矿体分为东区、中区及西 区。工程空间上，双层矿体共用一套开拓、采准、运输等开采系统；开采时序上，在提高铁矿生产能力的同时保证了钒矿开采的时间灵活性；采矿方法上，东区及西区铁矿采用阶段矿房嗣后膏体微胶结充填法，中区 铁矿采用阶段矿房法转崩落法；此外，通过中区崩落顶板及上盘围岩，东、西区膏体充填方式保证了矿区开采时及开采后的区域稳定性。研究表明：所提出的协同开采方案使矿山铁矿设计开采储量增加了1 064.7万t ，膏体充填每年消耗干抛层、尾矿等矿山固废86万t以上，矿山安全及经济效益明显。     

Simultaneous improvement of thermal conductivity and mechanical properties for mechanically mixed ABS/h-BN composites by using small amounts of hyperbranched polymer additives

Recently, thermal interface materials (TIMs) are in great demands for modern electronics. For mechanically mixed polymer composite TIMs, the thermal conductivity and the mechanical properties are generally lower than expected values due to the sharply increased viscosity and poor filler dispersion. This work shows that addition of a small amount of polyester-based hyperbranched polymer (HBP) avoided the trade-off in mechanically mixed ABS/hexagonal boron nitride (h-BN) composites. After adding 0.5 wt% HBP, the maximum h-BN content in the composites increased from 50 to 60 wt%. The out-of-plane, in-plane thermal conductivity, and tensile strength of ABS/h-BN with 50 wt% h-BN were 0.408, 0.517 W/mK, and 18 MPa, respectively, and were increased to 0.729, 0.847 W/mK, and 32 MPa by adding 0.5 wt% HBP, while 0.972, 1.12 W/mK, and 29.5 MPa were achieved for ABS/h-BN/HBP with 60 wt% h-BN. The morphological and rheological results proved that these enhancements are due to the improved h-BN dispersion by decreasing viscosity of composites during mixing. Theoretical modeling based on the modified effective medium theory confirmed such results and showed that the interfacial thermal resistance also decreased slightly. Thus, this work demonstrates a facile and scalable method for simultaneously improving the thermal conductivity and mechanical properties of thermoplastic-based TIMs.     

A mini review on two-dimensional nanomaterial assembly

Two-dimensional (2D) nanomaterials have attracted a great deal of attention since the discovery of graphene in 2004, due to their intriguing physicochemical properties and wide-ranging applications in catalysis, energy-related devices, electronics and optoelectronics. To maximize the potential of 2D nanomaterials for their technological applications, controlled assembly of 2D nanobulding blocks into integrated systems is critically needed. This mini review summarizes the reported strategies of 2D materials-based assembly into integrated functional nanostructures, from in-situ assembly method to post-synthesis assembly. The applications of 2D assembled integrated structures are also covered, especially in the areas of energy, electronics and sensing, and we conclude with discussion on the remaining challenges and potential directions in this emerging field.